BDS 3 Inch Lift Kit W/ Radius Arm FOX 2.5 Coil-Over Conversion - Performance Elite Ford F250/F350 Super Duty (23-24) 4WD (2201FPE)
BDS2201FPE, 013108, 013261, 123263, 123613
Price Match Guarantee
Free Factory Plus Protection Warranty!
FREE Shipping to the Lower 48 States!
This image is a representation of the product only. Actual product may vary in appearance.
Pricing:
$4,540.59
Description
Next level performance for your Super Duty with this 3" coilover conversion lift kit.
These kits are designed to improve performance and capability offroad while retaining great on-road handling. This kit builds on the BDS radius arm design to convert the front springs over to FOX 2.5 Performance Elite (PE) coilovers. These aluminum bodied coilovers offer improved damper performance, better heat dispersion and easy tuning via the DSC (dual speed compression) adjusters located on the reservoir allowing you to dial in the high-speed and low-speed compression settings. These coilovers come pre-tuned and full assembled to easy installation with the provided bolt-on coilover mounting brackets.
The foundation for this kit is the tried-and-true BDS radius arm lift kit that utilizes high strength tubular gusseted radius arms to correction front axle positioning, add strength and increase ground clearance. The kit also includes a HD adjustable track bar to recenter the front axle, sway bar relocation brackets, bump stop extensions, rear block & u-bolt kit along with FOX 2.0 Performance Series shocks at each corner. BDS designs this kit as a complete solution to transform your Super Duty to tame the any terrain.
Take your Super Duty to the next level with BDS and FOX.
These kits are designed to improve performance and capability offroad while retaining great on-road handling. This kit builds on the BDS radius arm design to convert the front springs over to FOX 2.5 Performance Elite (PE) coilovers. These aluminum bodied coilovers offer improved damper performance, better heat dispersion and easy tuning via the DSC (dual speed compression) adjusters located on the reservoir allowing you to dial in the high-speed and low-speed compression settings. These coilovers come pre-tuned and full assembled to easy installation with the provided bolt-on coilover mounting brackets.
The foundation for this kit is the tried-and-true BDS radius arm lift kit that utilizes high strength tubular gusseted radius arms to correction front axle positioning, add strength and increase ground clearance. The kit also includes a HD adjustable track bar to recenter the front axle, sway bar relocation brackets, bump stop extensions, rear block & u-bolt kit along with FOX 2.0 Performance Series shocks at each corner. BDS designs this kit as a complete solution to transform your Super Duty to tame the any terrain.
Take your Super Duty to the next level with BDS and FOX.
Prop 65 Notice
ATTENTION STATE OF CALIFORNIA CONSUMERS: *WARNING* Cancer and reproductive harm-www.p65warnings.ca.gov
Vehicle Fitment
Supplied Vehicle Information for 2201FPE
Important Kit Notes
1. This kit is not compatible with trucks equipped with radius arm mounted ride height sensors.
2. Designed for use on diesel models, but can be installed on gas trucks.
3. Will achieve additional 3/4" front ride height.
4. Installation requires a torque wrench capable of 406 ft-lbs.
5. Due to taller factory ride height, Tremor models will not net full advertised lift height. Final ride height will be the same as standard models.
6. Larger tires on stock wheel are not recommended due to interference with brake line, radius arm and sway bar. Use recommended specs listed in wheel and tire fitment section.
7. Trucks without top mounted overload spring will require (x4) UBT4031 available to purchase seperately.
Tire & Wheel Combinations
35" x 12.50 w/17 x 9 and 4.5-5" back spacing
35" x 12.50 w/18 x 9 and 4.5-5" back spacing
35" x 12.50 w/20 x 9 and back spacing
*Trimming may be required*
Est. Installation: 4-5 hours
Difficulty Level (easy 1 - 5 complicated): 3
2. Designed for use on diesel models, but can be installed on gas trucks.
3. Will achieve additional 3/4" front ride height.
4. Installation requires a torque wrench capable of 406 ft-lbs.
5. Due to taller factory ride height, Tremor models will not net full advertised lift height. Final ride height will be the same as standard models.
6. Larger tires on stock wheel are not recommended due to interference with brake line, radius arm and sway bar. Use recommended specs listed in wheel and tire fitment section.
7. Trucks without top mounted overload spring will require (x4) UBT4031 available to purchase seperately.
Tire & Wheel Combinations
35" x 12.50 w/17 x 9 and 4.5-5" back spacing
35" x 12.50 w/18 x 9 and 4.5-5" back spacing
35" x 12.50 w/20 x 9 and back spacing
*Trimming may be required*
Est. Installation: 4-5 hours
Difficulty Level (easy 1 - 5 complicated): 3
Details
- BDS2201FPE, 013108, 013261, 123263, 123613
- BDS2201FPE, 013108, 013261, 123263, 123613
- BDS Suspension
- New
Categories
Shipping Information
- Item Requires Shipping
- Free Shipping!
Customer Reviews
Total Reviews (0)
You must login to post a review.
Write the First Review!