BDS 5 Inch Lift Kit W/ Radius Arm Ford F250/F350 Super Duty (23-24) 4WD Diesel (2205FPE)
BDS2205FPE, 013414, 013459, 013516, 033411, 123263, 85431
Price Match Guarantee
Free Factory Plus Protection Warranty!
FREE Shipping to the Lower 48 States!
This image is a representation of the product only. Actual product may vary in appearance.
Pricing:
$4,913.69
Description
Next level performance for your Super Duty with this 5" radius arm lift kit with FOX Performance Elite shocks.
These kits are designed to improve performance and capability offroad while retaining great on-road handling. This kit builds on the stout BDS radius arm design and dual rate coil springs combined with FOX 2.5 Performance Elite (PE) shocks. These aluminum bodied shocks offer improved damper performance, better heat dispersion and easy tuning via the DSC (dual speed compression) adjusters located on the reservoir allowing you to dial in the high-speed and low-speed compression settings.
The foundation for this kit is the tried-and-true BDS radius arm lift kit that utilizes high strength tubular gusseted radius arms to correction front axle positioning, add strength and increase ground clearance. The kit also includes steering correction with a forged drop pitman arm along with a HD track bar bracket. Sway bar and brake line relocation brackets are utilized along with bump stop extensions. Fox 2.5" Performance Elite shocks and your choice of rear lift solutions to lift and level out the stance in the rear as well as dampen the harshest enviroments. BDS designs this kit as a complete solution to transform your Super Duty to tame the any terrain.
Take your Super Duty to the next level with BDS and FOX.
These kits are designed to improve performance and capability offroad while retaining great on-road handling. This kit builds on the stout BDS radius arm design and dual rate coil springs combined with FOX 2.5 Performance Elite (PE) shocks. These aluminum bodied shocks offer improved damper performance, better heat dispersion and easy tuning via the DSC (dual speed compression) adjusters located on the reservoir allowing you to dial in the high-speed and low-speed compression settings.
The foundation for this kit is the tried-and-true BDS radius arm lift kit that utilizes high strength tubular gusseted radius arms to correction front axle positioning, add strength and increase ground clearance. The kit also includes steering correction with a forged drop pitman arm along with a HD track bar bracket. Sway bar and brake line relocation brackets are utilized along with bump stop extensions. Fox 2.5" Performance Elite shocks and your choice of rear lift solutions to lift and level out the stance in the rear as well as dampen the harshest enviroments. BDS designs this kit as a complete solution to transform your Super Duty to tame the any terrain.
Take your Super Duty to the next level with BDS and FOX.
Prop 65 Notice
ATTENTION STATE OF CALIFORNIA CONSUMERS: *WARNING* Cancer and reproductive harm-www.p65warnings.ca.gov
Vehicle Fitment
Supplied Vehicle Information for BDS2205FPE
Important Kit Notes
1. This kit is not compatible with trucks equipped with radius arm mounted ride height sensors.
2. Ford recommends replacement of the pitman arm nut after each time it has been removed.
3. Use a small pitman arm puller to remove the drag link joint and steering stabilizer taper.
4. If your truck is equipped with a 2-piece rear driveshaft, a Carrier Bearing Drop Kit may be required: BDS123402.
5. Due to taller factory ride height, Tremor models will not net full advertised lift height. Final ride height will be the same as standard models.
6. Larger tires on stock wheel are not recommended due to interference with brake line, radius arm and sway bar. Use recommended specs listed in wheel and tire fitment section.
7. Minor trimming may be necessary for clearance of 37x12.50 tires on certain wheel setups.
8. Installation requires a torque wrench capable of 406 ft-lbs.
9. Trucks without top mounted overload springs will require (4) UBT4028.
Tire & Wheel Combinations
37" x 12.50 w/17 x 9 and 4.5-5" back spacing
37" x 12.50 w/18 x 9 and 4.5-5" back spacing
37" x 12.50 w/20 x 9 and back spacing
*Trimming may be required*
Est. Installation: 4-5 hours
Difficulty Level (easy 1 - 5 complicated): 3
2. Ford recommends replacement of the pitman arm nut after each time it has been removed.
3. Use a small pitman arm puller to remove the drag link joint and steering stabilizer taper.
4. If your truck is equipped with a 2-piece rear driveshaft, a Carrier Bearing Drop Kit may be required: BDS123402.
5. Due to taller factory ride height, Tremor models will not net full advertised lift height. Final ride height will be the same as standard models.
6. Larger tires on stock wheel are not recommended due to interference with brake line, radius arm and sway bar. Use recommended specs listed in wheel and tire fitment section.
7. Minor trimming may be necessary for clearance of 37x12.50 tires on certain wheel setups.
8. Installation requires a torque wrench capable of 406 ft-lbs.
9. Trucks without top mounted overload springs will require (4) UBT4028.
Tire & Wheel Combinations
37" x 12.50 w/17 x 9 and 4.5-5" back spacing
37" x 12.50 w/18 x 9 and 4.5-5" back spacing
37" x 12.50 w/20 x 9 and back spacing
*Trimming may be required*
Est. Installation: 4-5 hours
Difficulty Level (easy 1 - 5 complicated): 3
Details
- BDS2205FPE, 013414, 013459, 013516, 033411, 123263, 85431
- BDS2205FPE, 013414, 013459, 013516, 033411, 123263, 85431
- BDS Suspension
- New
Categories
Shipping Information
- Item Requires Shipping
- Free Shipping!
Customer Reviews
Total Reviews (0)
You must login to post a review.
Write the First Review!